2 Channel relay board for your Arduino or Raspberry PI - 12V 價格比較,價格查詢,歷史價格詳細信息

2 Channel relay board for your Arduino or Raspberry PI - 12V 價格比較,價格查詢,價格歷史信息

Name: 2 Channel relay board for your Arduino or Raspberry PI - 12V
SKU: 6440668-8502783869

2 Channel relay board for your Arduino or Raspberry PI - 12V 規格

2 Channel relay board for your Arduino or Raspberry PI - 12V 最新價格

facebook linkedin mastodon messenger pinterest reddit telegram twitter viber vkontakte whatsapp 複製鏈接

2 Channel relay board for your Arduino or Raspberry PI - 12V 歷史價格(單位:新台幣)

2 Channel relay board for your Arduino or Raspberry PI - 12V 描述

適用於Arduino或Raspberry PI的2通道繼電器板-12V 通用2 SPDT通道繼電器板（電源12VDC），用於切換大電流電氣負載（AC和DC），例如電動機，燈，泵，接觸器等。使用該繼電器板，可以使用從3V到30V的任何邏輯電平信號來激活繼電器（也可以通過微控制器TTL邏輯對其進行直接控制）。它可以成功用於PIC，AVR，ARM微控制器，Raspberry PI，Arduino輸出等。特徵電源要求-12VDC；電流消耗-100mA（所有繼電器均打開時）； 2個SPDT中繼通道（類型取決於我們商店中的庫存數量）：銅陵-JQC-3FF-S-Z（10A / 250VAC，15A / 120VAC，10A / 28VDC） SUNHOLD-RAS xx15（10A / 250VAC，15A / 120VAC，15A / 24VDC）觸點類型：常開（NO），常閉（NC）；螺絲端子用於輸入和輸出； PCB參數：FR4 / 1.5mm /兩層/金屬化孔/ HAL /白色印章/阻焊層; 額外的PCB開口可實現更好的電壓隔離；高電流軌道加倍；每個繼電器的保護二極管；輸入電壓：必須為“ In”提供3V-30V（最大1.5mA），才能打開繼電器。可以由TTL直接控制；綠色LED指示繼電器狀態；紅色指示電源；尺寸：85mm / 37mm / 20mm; 安裝孔直徑：3mm； PCB尺寸-此處； 2 Channel relay board for your Arduino or Raspberry PI - 12V A general purpose 2 SPDT channel relay board (power supply 12VDC) for switching high-current electrical loads (both AC and DC) such as motors, lights, pumps, contactors and more. With this relay board, any logic-level signal from 3V up to 30V can be used to activate a relay (it may be controlled direclty by microcontroller TTL logic as well). It can be used successfully for example with PIC,AVR,ARM microcontroller, Raspberry PI, Arduino outputs and other. Features Power supply requirement - 12VDC; Current consumption - 100mA (when all relays are ON); 2 SPDT relay channels (the type depends on the stocks quantity in our store): TONGLING - JQC-3FF-S-Z (10A / 250VAC, 15A / 120VAC, 10A / 28VDC) SUNHOLD - RAS xx15 (10A / 250VAC, 15A / 120VAC, 15A / 24VDC) Contact type: Normal Opened (NO), Normal Closed (NC); Screw terminals for inputs and outputs; PCB parameters : FR4 / 1.5mm / two layers / metallized holes / HAL / white stamp / solder mask; Extra PCB openings for better voltage isolation; Doubled high current tracks; Protection diode for each relay; Input voltage: 3V - 30V (1.5mA max) must be given to the "In" to switch the relay ON; May be controlled directly by TTL; Green leds for relay status; Red led for power; Dimensions: 85mm / 37mm / 20mm; Mounting holes diameter: 3mm; PCB dimensions - here;